3.1 Basics

Let us first survey some basic concepts necessary to use a macro package fruitfully.6 References are made throughout to more detailed information.

GNU troff reads an input file prepared by the user and outputs a formatted document suitable for publication or framing. The input consists of text, or words to be printed, and embedded commands (requests and escape sequences), which tell GNU troff how to format the output. See Formatter Instructions.

The word argument is used in this chapter to mean a word or number that appears on the same line as a request, and which modifies the meaning of that request. For example, the request

.sp

spaces one line, but

.sp 4

spaces four lines. The number 4 is an argument to the sp request, which says to space four lines instead of one. Arguments are separated from the request and from each other by spaces (not tabs). See Invoking Requests.

The primary function of GNU troff is to collect words from input lines, fill output lines with those words, adjust the line to the right-hand margin by widening spaces, and output the result. For example, the input:

Now is the time
for all good men
to come to the aid
of their party.
Four score and seven
years ago, etc.

is read, packed onto output lines, and justified to produce:

  ⇒ Now is the time for all good men to come to the aid of
  ⇒ their party.  Four score and seven years ago, etc.

Sometimes a new output line should be started even though the current line is not yet full—for example, at the end of a paragraph. To do this it is possible to force a break, starting a new output line. Some requests cause a break automatically, as do (normally) blank input lines and input lines beginning with a space or tab.

Not all input lines are text lines—words to be formatted. Some are control lines that tell a macro package (or GNU troff directly) how to format the text. Control lines start with a dot (‘.’) or an apostrophe (‘'’) as the first character, and can be followed by a macro call.

The formatter also does more complex things, such as automatically numbering pages, skipping over page boundaries, putting footnotes in the correct place, and so forth.

Here are a few hints for preparing text for input to GNU troff.

We offer further advice in Input Conventions.

GNU troff permits alteration of the distance between lines of text. This is termed vertical spacing and is expressed in the same units as the type size—the point. The default is 10-point type on 12-point spacing. To get double-spaced text you would set the vertical spacing to 24 points. Some, but not all, macro packages expose a macro or register to configure the vertical spacing.

A number of requests allow you to change the way the output is arranged on the page, sometimes called the layout of the output page. Most macro packages don’t supply macros for performing these (at least not without performing other actions besides), as they are such basic operations. The macro packages for writing man pages, man and mdoc, don’t encourage explicit use of these requests at all.

The request ‘.sp N leaves N lines of blank space. N can be omitted (skipping a single line) or can be of the form Ni (for N inches) or Nc (for N centimeters). For example, the input:

.sp 1.5i
My thoughts on the subject
.sp

leaves one and a half inches of space, followed by the line “My thoughts on the subject”, followed by a single blank line (more measurement units are available; see Measurements).

If you seek precision in spacing, be advised when using a macro package that it might not honor sp requests as you expect; it can use a formatter feature called no-space mode to prevent excess space from accumulating. Macro packages typically offer registers to control spacing between paragraphs, before section headings, and around displays (discussed below); use these facilities preferentially. See Manipulating Spacing.

Text lines can be centered by using the ce request. The line after ce is centered (horizontally) on the page. To center more than one line, use ‘.ce N (where N is the number of lines to center), followed by the N lines. To center many lines without counting them, type:

.ce 1000
lines to center
.ce 0

The ‘.ce 0 request tells GNU troff to center zero more lines, in other words, stop centering.

GNU troff also offers the rj request for right-aligning text. It works analogously to ce and is convenient for setting epigraphs.

The bp request starts a new page; this necessarily implies an ordinary (line) break.

All of these requests cause a break; that is, they always start a new line. To start a new line without performing any other action, use br. If you invoke them with the apostrophe ‘'’, the no-break control character, the (initial) break they normally perform is suppressed. ‘'br’ does nothing.