-*- Text -*- This is the GRUB. Welcome. This file contains instructions for compiling and installing the GRUB. The Requirements ================ GRUB depends on some software packages installed into your system. If you don't have any of them, please obtain and install them before configuring the GRUB. * GCC 5.1.0 or later Experimental support for clang 3.8.0 or later (results in much bigger binaries) for i386, x86_64, arm (including thumb), arm64, mips(el), powerpc, sparc64 * GNU Make * GNU Bison 2.3 or later * GNU gettext 0.17 or later * GNU binutils 2.9.1.0.23 or later * Flex 2.5.35 or later * pkg-config * Other standard GNU/Unix tools * a libc with large file support (e.g. glibc 2.1 or later) On GNU/Linux, you also need: * libdevmapper 1.02.34 or later (recommended) For optional grub-emu features, you need: * SDL (recommended) * libpciaccess (optional) * libusb (optional) To build GRUB's graphical terminal (gfxterm), you need: * FreeType 2.1.5 or later * GNU Unifont If you use a development snapshot or want to hack on GRUB you may need the following. * Python 2.6 or later * Autoconf 2.63 or later * Automake 1.11 or later Prerequisites for make-check: * qemu, specifically the binary 'qemu-system-i386' * xorriso 1.2.9 or later, for grub-mkrescue and grub-shell Configuring the GRUB ==================== The `configure' shell script attempts to guess correct values for various system-dependent variables used during compilation. It uses those values to create a `Makefile' in each directory of the package. It may also create one or more `.h' files containing system-dependent definitions. Finally, it creates a shell script `config.status' that you can run in the future to recreate the current configuration, a file `config.cache' that saves the results of its tests to speed up reconfiguring, and a file `config.log' containing compiler output (useful mainly for debugging `configure'). If you need to do unusual things to compile the package, please try to figure out how `configure' could check whether to do them, and mail diffs or instructions to the address given in the `README' so they can be considered for the next release. If at some point `config.cache' contains results you don't want to keep, you may remove or edit it. The file `configure.ac' is used to create `configure' by a program called `autoconf'. You only need `configure.in' if you want to change it or regenerate `configure' using a newer version of `autoconf'. Building the GRUB ================= The simplest way to compile this package is: 1. `cd' to the directory containing the package's source code. 2. Skip this and following step if you use release tarball and proceed to step 4. If you want translations type `./linguas.sh'. 3. Type `./bootstrap'. * autogen.sh (called by bootstrap) uses python. By default the invocation is "python", but it can be overridden by setting the variable $PYTHON. 4. Type `./configure' to configure the package for your system. If you're using `csh' on an old version of System V, you might need to type `sh ./configure' instead to prevent `csh' from trying to execute `configure' itself. Running `configure' takes awhile. While running, it prints some messages telling which features it is checking for. 6. Type `make' to compile the package. 7. Optionally, type `make check' to run any self-tests that come with the package. 8. Type `make install' to install the programs and any data files and documentation. 9. You can remove the program binaries and object files from the source code directory by typing `make clean'. To also remove the files that `configure' created (so you can compile the package for a different kind of computer), type `make distclean'. There is also a `make maintainer-clean' target, but that is intended mainly for the package's developers. If you use it, you may have to get all sorts of other programs in order to regenerate files that came with the distribution. Cross-compiling the GRUB ======================== GRUB defines 3 platforms: - "Build" is the one which build systems runs on. - "Host" is where you execute GRUB utils. - "Target" is where GRUB itself runs. For grub-emu host and target must be the same but may differ from build. If build and host are different make check isn't available. If build and host are different man pages are not generated. As an example imagine you have a build system running on FreeBSD on sparc which prepares packages for developers running amd64 GNU/Linux laptop and they need to make images for ARM board running U-boot. In this case: build=sparc64-freebsd host=amd64-linux-gnu target=arm-uboot For this example the configure line might look like (more details below) (some options are optional and included here for completeness but some rarely used options are omitted): ./configure --host=x86_64-linux-gnu --target=arm-linux-gnueabihf \ --with-platform=efi BUILD_CC=gcc BUILD_PKG_CONFIG=pkg-config \ HOST_CC=x86_64-linux-gnu-gcc HOST_CFLAGS='-g -O2' \ PKG_CONFIG=x86_64-linux-gnu-pkg-config TARGET_CC=arm-linux-gnueabihf-gcc \ TARGET_CFLAGS='-Os -march=armv8.3-a' TARGET_CCASFLAGS='-march=armv8.3-a' \ TARGET_OBJCOPY=arm-linux-gnueabihf-objcopy \ TARGET_STRIP=arm-linux-gnueabihf-strip TARGET_NM=arm-linux-gnueabihf-nm \ TARGET_RANLIB=arm-linux-gnueabihf-ranlib LEX=flex Normally, for building a GRUB on amd64 with tools to run on amd64 to generate images to run on ARM, using your Linux distribution's packaged cross compiler, the following would suffice: ./configure --target=arm-linux-gnueabihf --with-platform=efi You need to use following options to specify tools and platforms. For minimum version look at prerequisites. All tools not mentioned in this section under corresponding platform are not needed for the platform in question. - For build 1. BUILD_CC= to gcc able to compile for build. This is used, for example, to compile build-gentrigtables which is then run to generate sin and cos tables. 2. BUILD_CFLAGS= for C options for build. 3. BUILD_CPPFLAGS= for C preprocessor options for build. 4. BUILD_LDFLAGS= for linker options for build. 5. BUILD_PKG_CONFIG= for pkg-config for build (optional). - For host 1. --host= to autoconf name of host. 2. CC= for gcc able to compile for host. 3. CFLAGS= for C options for host. 4. HOST_CC= for gcc able to compile for host. 5. HOST_CFLAGS= for C options for host. 6. HOST_CPPFLAGS= for C preprocessor options for host. 7. HOST_LDFLAGS= for linker options for host. 8. PKG_CONFIG= for pkg-config for host (optional). 9. Libdevmapper if any must be in standard linker folders (-ldevmapper) (optional). 10. Libfuse if any must be in standard linker folders (-lfuse) (optional). 11. Libzfs if any must be in standard linker folders (-lzfs) (optional). 12. Liblzma if any must be in standard linker folders (-llzma) (optional). Note: The HOST_* variables override not prefixed variables. - For target 1. --target= to autoconf cpu name of target. 2. --with-platform to choose firmware. 3. TARGET_CC= for gcc able to compile for target. 4. TARGET_CFLAGS= for C options for target. 5. TARGET_CPPFLAGS= for C preprocessor options for target. 6. TARGET_CCASFLAGS= for assembler options for target. 7. TARGET_LDFLAGS= for linker options for target. 8. TARGET_OBJCOPY= for objcopy for target. 9. TARGET_STRIP= for strip for target. 10. TARGET_NM= for nm for target. 11. TARGET_RANLIB= for ranlib for target. Note: If the TARGET_* variables are not specified then they will default to be the same as the host variables. If host variables are not specified then the TARGET_* variables will default to be the same as not prefixed variables. - Additionally for emu, for host and target. 1. SDL is looked for in standard linker directories (-lSDL) (optional) 2. libpciaccess is looked for in standard linker directories (-lpciaccess) (optional) 3. libusb is looked for in standard linker directories (-lusb) (optional) - Platform-agnostic tools and data. 1. make is the tool you execute after ./configure. 2. Bison is specified in YACC= variable 3. Flex is specified in LEX= variable 4. GNU unifont and Djvu sans are looked for in standard directories. Compiling For Multiple Architectures ==================================== You can compile the package for more than one kind of computer at the same time, by placing the object files for each architecture in their own directory. `cd' to the directory where you want the object files and executables to go and run the `configure' script. `configure' automatically checks for the source code in the directory that `configure' is in and in `..'. Installation Names ================== By default, `make install' will install the package's files in `/usr/local/bin', `/usr/local/man', etc. You can specify an installation prefix by giving `configure' the option `--prefix=PATH'. You can specify separate installation prefixes for architecture-specific files and architecture-independent files. If you give `configure' the option `--exec-prefix=PATH', the package will use PATH as the prefix for installing programs and libraries. Documentation and other data files will still use the regular prefix. In addition, if you use an unusual directory layout you can give options like `--bindir=PATH' to specify different values for particular kinds of files. Run `configure --help' for a list of the directories you can set and what kinds of files go in them. If the package supports it, you can cause programs to be installed with an extra prefix or suffix on their names by giving `configure' the option `--program-prefix=PREFIX' or `--program-suffix=SUFFIX'. Please note, however, that the GRUB knows where it is located in the filesystem. If you have installed it in an unusual location, the system might not work properly, or at all. The chief utility of these options for the GRUB is to allow you to "install" in some alternate location, and then copy these to the actual root filesystem later. Sharing Defaults ================ If you want to set default values for `configure' scripts to share, you can create a site shell script called `config.site' that gives default values for variables like `CC', `cache_file', and `prefix'. `configure' looks for `PREFIX/share/config.site' if it exists, then `PREFIX/etc/config.site' if it exists. Or, you can set the `CONFIG_SITE' environment variable to the location of the site script. A warning: not all `configure' scripts look for a site script. Operation Controls ================== `configure' recognizes the following options to control how it operates. `--cache-file=FILE' Use and save the results of the tests in FILE instead of `./config.cache'. Set FILE to `/dev/null' to disable caching, for debugging `configure'. `--help' Print a summary of the options to `configure', and exit. `--quiet' `--silent' `-q' Do not print messages saying which checks are being made. `--srcdir=DIR' Look for the package's source code in directory DIR. Usually `configure' can determine that directory automatically. `--version' Print the version of Autoconf used to generate the `configure' script, and exit.