Modern disk image formats allow users to create an overlay on top of an existing image which will be the target of the new guest writes. This allows us to do snapshots of the disk state of a VM efficiently. The following text describes how libvirt manages such image chains and some problems which can occur. Note that many of the cases mentioned below are currently only relevant for the qemu driver.
Contents
Disk image chains can be partially or fully configured in the domain XML. The basic approach is to use the <backingStore> elements in the configuration.
The <backingStore> elements present in the live VM xml represent the actual topology that libvirt knows of.
Any default configuration or example usually refers only to the top (active) image of the backing chain.
<disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/tmp/pull4.qcow2'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x0a' function='0x0'/> </disk>
This configuration will prompt libvirt to detect the backing image of the source image and recursively do the same thing until the end of the chain.
The disk image locations are used by libvirt to properly set up the security system used on the host so that the hypervisor can access the files; it can also be used to configure the hypervisor to use the appropriate images. Thus it's important to properly set up the formats and paths of the backing images.
Any externally created image should always use the -F switch of qemu-img to specify the format of the backing file to avoid probing.
Detection of the backing chain requires libvirt to read and understand the backing file field recorded in the image metadata and also being able to recurse and read the backing file. Due to security implications libvirt will refuse to use backing images of any image whose format was not specified explicitly in the XML or the overlay image itself.
Libvirt also might lack support for a network disk storage technology and thus may be unable to visit and detect backing chains on such storage. This may result in the backing chain in the live XML looking incomplete or some operations not being possible. To prevent this it's possible to specify the image metadata explicitly in the XML.
To specify the topology of disk images explicitly the following XML specification can be used:
<disk type='file' device='disk'>
<driver name='qemu' type='qcow2'/>
<source file='/tmp/pull4.qcow2'/>
<backingStore type='file'>
<format type='qcow2'/>
<source file='/tmp/pull3.qcow2'/>
<backingStore type='file'>
<format type='qcow2'/>
<source file='/tmp/pull2.qcow2'/>
<backingStore type='file'>
<format type='qcow2'/>
<source file='/tmp/pull1.qcow2'/>
<backingStore type='file'>
<format type='qcow2'/>
<source file='/tmp/pull0.qcow2'/>
<backingStore/>
</backingStore>
</backingStore>
</backingStore>
</backingStore>
<target dev='vda' bus='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x0a' function='0x0'/>
</disk>
This makes libvirt follow the settings as configured in the XML. Note that this is supported only when the https://libvirt.org/formatdomaincaps.html#backingstoreinput capability is present.
An empty <backingStore/> element signals the end of the chain. Using this will prevent libvirt or qemu from probing the backing chain.
Note that it's also possible to partially specify the chain in the XML but omit the terminating element. This will result in probing from the last specified <backingStore>
Any image specified explicitly will not be probed for backing file or format.
When creating disk images manually outside of libvirt it's important to create them properly so that they work with libvirt as expected. The created disk images must contain the format of the backing image in the metadata. This means that the -F parameter of qemu-img must always be used.
qemu-img create -f qcow2 -F qcow2 -b $BACKING_IMAGE_PATH $IMAGE_PATH
Note that if $BACKING_IMAGE_PATH is relative the path is considered relative to the location of $IMAGE_PATH.
A few common problems which occur when managing chains of disk images.
This problem happens on VMs where the backing chain was created manually outside of libvirt and can have multiple symptoms:
permission denied error reported on a backing image
format of backing image '%s' of image '%s' was not specified in the image metadata error reported
disk image looking corrupt inside the guest
The cause of the above problem is that the image metadata does not record the format of the backing image along with the location of the image. When the format is not specified libvirt or qemu would have to do image format probing which is insecure to do as a malicious guest could rewrite the header of the disk leading to access of host files. Libvirt thus does not try to assume the format of the backing image. The following command can be used to check if the image has a backing image format specified:
$ qemu-img info /tmp/copy4.qcow2
image: /tmp/copy4.qcow2
file format: qcow2
virtual size: 10 MiB (10485760 bytes)
disk size: 196 KiB
cluster_size: 65536
backing file: copy3.qcow2 (actual path: /tmp/copy3.qcow2)
backing file format: qcow2
Format specific information:
compat: 1.1
lazy refcounts: false
refcount bits: 16
corrupt: false
If the backing file format field is missing above the format was not specified properly. The image can be fixed by the following command:
qemu-img rebase -f $IMAGE_FORMAT -F $BACKING_IMAGE_FORMAT -b $BACKING_IMAGE_PATH $IMAGE_PATH
It is important to fill out $BACKING_IMAGE_FORMAT and $IMAGE_FORMAT properly. $BACKING_IMAGE_PATH should be specified as a full absolute path. If relative referencing of the backing image is desired, the path must be relative to the location of image described by $IMAGE_PATH.
Important: If the $BACKING_IMAGE_FORMAT is not known it can be queried using qemu-img info $BACKING_IMAGE_PATH and looking for the file format field, but for security reasons the value should be used only if at least one of the following criteria is met:
file format is raw
backing file is NOT present
backing file is present AND is correct/trusted
Note that the last criterion may require manual inspection and thus should not be scripted unless the trust for the image can be expressed programmatically.
Also note that the above steps may need to be repeated recursively for any subsequent backing images.
The path to the backing image which is recorded in the image metadata often contains a full path to the backing image. This is the default libvirt-created image configuration. When such images are moved to a different location the top image will no longer point to the correct image.
To fix such issue you can either fully specify the image chain in the domain XML as pointed out above or the following qemu-img command can be used:
qemu-img rebase -u -f $IMAGE_FORMAT -F $BACKING_IMAGE_FORMAT -b $BACKING_IMAGE_PATH $IMAGE_PATH
It is important to fill out $BACKING_IMAGE_FORMAT and $IMAGE_FORMAT properly. $BACKING_IMAGE_PATH should be specified as a full absolute path. If relative referencing of the backing image is desired, the path must be relative to the location of image described by $IMAGE_PATH.